[vc_row][vc_column width=”1/1″][vc_column_text]

Other Attachments

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”1/1″][vc_column_text]Evans & Reid offer a full bespoke service for equipment and attachments; products that are manufactured to your specific requirements including: Riddle Buckets, Trapezoidal “V” Type Trenching buckets, Underpinning Bucket, Grave Digging Bucket, Deep Digging Bucket,Land & Stone Rakes, Adaptor Plates for Hammers And Other Attachments, Interlocking Tine Grabs, Spring Type Manual Quick Hitch, “Semi” – Quick Hitch, Turf Lifter, Kerb Stone Hydraulic Grab and Clay Buckets.[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Turf Lifter

These buckets are specially designed to lift turf from a surface.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Turflifter Side Panell

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Adaptor plates for hammers and other attachments

We manufacture hammer tops for all the manufacturers of breakers and provide adaptor plates for any attachment needed to be fitted to an excavator.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Hammertop Side Panel

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Aerator

This is a device which is used to break up clay by putting holes down from the surface, which normally are then filled with sand.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Aerator

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Adjustable Canal /river bed cleaning dozer blade

This can be mounted on the dipper arm, or on the excavator dozer blade. It has variable width wings which have rubber skirts attached.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Canal Dozer

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Wheelie Bin Attachment

Bespoke attachment specially designed for handling and emptying wheelie bins.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Wheelie Bin Side Panel

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Wire Fence Un-winder

Place a roll of pigmesh over the red pole, staple it to the first two posts and track the excavator along the fence line attaching as you go.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Wire Fence Unwinder Side Panel

[/vc_column_text][/vc_column][/vc_row][vc_row][vc_column width=”2/3″][vc_column_text]

Back-fill Blade

This is an attachment which allows an excavator to quickly fill a trench with the spoil which was removed. It has a an adjustable top plate to vary the angle. This system has been used to speedily refill trenches especially where there is an obstruction (such as a wall) on the side the removed spoil has been deposited.[/vc_column_text][/vc_column][vc_column width=”1/3″][vc_column_text]

Back-Fill Blade Side Panel

[/vc_column_text][/vc_column][/vc_row]

0